Tile Xtraa TX 205 | Premium Tile Adhesives by Sakarni

Tile Xtraa TX 205

High-Performance Grey Cementitious Tile Adhesive

Sakarni Tile Xtraa TX 205 is a professional-grade, grey cement-based polymer-modified tile adhesive engineered for reliable floor and wall installations. Powered by advanced Hydro Holder Strong Bond Technology, it delivers an exceptional surface grip, reliable water resistance, and high-build bedding stability. It completely eliminates the need for traditional on-site tile soaking or post-installation water curing, significantly boosting construction productivity while providing an exceptionally cost-effective solution for high-volume interior tiling layouts.

Hydro Holder
Hydro Holder
Strong Bond
Advance Technology
Xtraa
Xtraa
Productivity
& Time Saving
0%
0%
Water Curing
Required

Engineered to Protect Tiled Layouts from Sagging, Hollow Pockets & Debonding Failures

Conventional Cement Mortars

Traditional systems often suffer from:

Severe drying shrinkage causing rapid tile debonding and structural pop-outs
High water permeability leading to moisture seepage and joint efflorescence
Poor sag resistance making vertical wall installations highly difficult

Tile Xtraa TX 205

It is specially formulated to provide:

High-polymer molecular grip preventing tiles from sagging on vertical wall faces
Specialized non-shrink matrix that eliminates under-tile voids and hollow sounds
High water resistance properties ideal for wet-area tile backgrounds
Accelerated curing mechanism requiring absolutely no pre-soaking or post-watering

Key Benefits

Key Benefits

Hydro holder strong bond
Increases layout installation productivity
Highly water resistant formula
No site curing needed
Highly cost effective choice
Excellent vertical non-sag grip

Hydro holder strong bond
Increases layout installation productivity
Highly water resistant formula
No site curing needed
Highly cost effective choice
Excellent vertical non-sag grip

No site curing needed
Highly cost effective choice
Excellent vertical non-sag grip

where to use

1
Floor Installations
General residential ceramic floor tiling
High-traffic internal commercial walkways
Vitrified tile floor layouts
2
Interior Walls
Bathroom and restroom wall tiling
Kitchen dado wall installations
General internal masonry partitions
3
Home Renovations
Replacing old damaged floor tiles
Modernizing internal residential laundry zones
Refurbishing small residential utility balconies

1
Floor Installations
General residential ceramic floor tiling
High-traffic internal commercial walkways
Vitrified tile floor layouts
2
Interior Walls
Bathroom and restroom wall tiling
Kitchen dado wall installations
General internal masonry partitions
3
Home Renovations
Replacing old damaged floor tiles
Modernizing internal residential laundry zones
Refurbishing small residential utility balconies

application process

Surface Preparation

Clean the floor or wall masonry substrate thoroughly to eliminate all dust, traces of oil, grease, laitance, and loose curing compounds.

Correct major surface irregularities, deep crevices, and layout depressions using a polymer-modified repair mortar before execution.
Ensure that newly cast concrete floor slabs or cement-plastered walls are completely cured, stable, and geometrically true.
Dampen highly porous cement plaster zones lightly with potable water and allow the wet sheen to dissipate prior to adhesive laying.

Application

Mix the white adhesive powder with a measured volume of clean potable water using a mechanical slow-speed paddle mixer.

Allow the homogeneous, creamy white paste to slake inside the mixing container for five minutes, then blend it briefly once more.
Trowel the mixed white adhesive paste firmly onto the structural background using the flat edge of a notched trowel.
Comb the wet bed with a suitable notched profile tool at a sixty-degree angle to produce uniform parallel ribs.

FInishing

Press the white marble stone or glass tiles firmly into the ribbed wet white adhesive bed with an adaptive sliding movement.

Use a rubber mallet or grout float to tap the stone sections smoothly, guaranteeing complete back-surface wetting.
Clean out any wet adhesive squeezing out into the joint channels immediately using a damp sponge or cloth.
Allow the completed stone matrix to cure undisturbed for twenty-four hours before initiating joint grouting operations.

Surface Preparation

Clean the floor or wall masonry substrate thoroughly to eliminate all dust, traces of oil, grease, laitance, and loose curing compounds.

Correct major surface irregularities, deep crevices, and layout depressions using a polymer-modified repair mortar before execution.
Ensure that newly cast concrete floor slabs or cement-plastered walls are completely cured, stable, and geometrically true.
Dampen highly porous cement plaster zones lightly with potable water and allow the wet sheen to dissipate prior to adhesive laying.

Application

Mix the white adhesive powder with a measured volume of clean potable water using a mechanical slow-speed paddle mixer.

Allow the homogeneous, creamy white paste to slake inside the mixing container for five minutes, then blend it briefly once more.
Trowel the mixed white adhesive paste firmly onto the structural background using the flat edge of a notched trowel.
Comb the wet bed with a suitable notched profile tool at a sixty-degree angle to produce uniform parallel ribs.

FInishing

Press the white marble stone or glass tiles firmly into the ribbed wet white adhesive bed with an adaptive sliding movement.

Use a rubber mallet or grout float to tap the stone sections smoothly, guaranteeing complete back-surface wetting.
Clean out any wet adhesive squeezing out into the joint channels immediately using a damp sponge or cloth.
Allow the completed stone matrix to cure undisturbed for twenty-four hours before initiating joint grouting operations.

Important Note

Surface Preparation

Surface Preparation

Apply only on properly prepared and structurally sound masonry surfaces. Follow recommended surface preparation and application practices to achieve optimum durability and a flawless finish.

Technical properties

Property	Description
Product Type	Grey Cementitious Tile Adhesive
Appearance	Grey Granular Powder
Finish	High-Strength Solid Adhesive Bed
Key Feature	Hydro Holder Strong Bond
Water Resistance	High
Sag Resistance	Excellent
Pre-Soaking / Curing	Not Required
Open Time	High Workability Range
Application Method	Notched Trowel
Surface Compatibility	Cement Plaster, Concrete Slabs & Masonry
Application Area	Interior Floors and Walls
Packing	Available in Standard Packs
Shelf Life	As per sealed pack conditions

Property	Description
Product Type	Grey Cementitious Tile Adhesive
Appearance	Grey Granular Powder
Finish	High-Strength Solid Adhesive Bed
Key Feature	Hydro Holder Strong Bond
Water Resistance	High
Sag Resistance	Excellent
Pre-Soaking / Curing	Not Required
Open Time	High Workability Range
Application Method	Notched Trowel
Surface Compatibility	Cement Plaster, Concrete Slabs & Masonry
Application Area	Interior Floors and Walls
Packing	Available in Standard Packs
Shelf Life	As per sealed pack conditions

Explore More of Sakarni's Catalogue

Explore More of Sakarni's Catalogue

Frequently Asked Questions

1. What is it used for?

2. Can it be used outdoors?

3. Do I need to cure the tiles with water after fixing?

4. Is it ready to use or does it require mixing?

5. How does it prevent hollow tile spots?

Download our Apps

Sakarni Premium Club

iMIdAS-Sakarni Bandhan

Follow Our Journey

© 2026 All Rights Reserved. Sakarni Plaster Pvt Ltd. Cookie Preferences